Working as an Elsmere commercial roof repair contractor, we trace leaks across shared strip center roofs and repair the seam, scupper, or curb at fault.
An Elsmere commercial roof repair contractor works across tenant lines here, because attached storefronts along Dixie Highway share one long roof and water ignores the walls below.
A stain over one storefront can start above the shop next door. Parapets, scuppers, and rooftop units run the length of the building, and each tenant's HVAC service adds its own cuts and seals to the membrane.
Strip roofs with a long repair history carry patches from many earlier jobs. Records of past work help sort out which patches still hold and which one is the source.
Shared roofs collect problems from every tenant. These four show up most.
New stains after a tenant's rooftop unit was serviced or swapped.
Each tenant's contractor works its own unit. Torn base flashing or an unsealed curb opening lets water travel under the membrane toward a neighbor's ceiling.
Water marks high on the parapet wall after storms.
A clogged scupper lets water rise past the base flashing. It then finds gaps behind the coping and drips into whichever unit sits below.
Patches on top of patches near the same curb.
Several past repairs in mixed materials stop bonding to each other. Old cement comes off and a matching patch goes on in its place.
Drips along the line of a demising wall inside.
Long roof runs move with temperature, and seams over tenant walls take the strain. Rewelding or retaping them closes the path.
On a shared roof, one fixed source can stop leaks in two or three storefronts at once.
Repairing the true source over the right unit ends the drip in the shop next door, instead of patching the ceiling where the water happens to land.
CurbsPhotos and notes tied to each roof section show landlords and tenants which patches are new, which are holding, and where to watch next.
RecordsCleared and resealed scuppers keep water from rising behind the coping, the path that sends one storm into several units.
ScuppersRewelded seams along demising walls stand up to the movement of a long roof run through freeze and thaw.
SeamsStrip centers in Elsmere use all four repair types, often on one roof.
Most Elsmere storefront rows sit under one low-slope membrane, so seams over demising walls and curb corners get rewelded or retaped where they opened.
Flat roof repair for storefront rows
Rear additions, canopies, and storage sheds behind the storefronts often carry metal panels with their own screw and lap leaks.
Metal roof repair for rear additions
Tracing across tenant lines finds which unit's curb, scupper, or pipe boot is behind a stain two doors down.
Leak tracing across tenant lines
Restaurant tenants vent grease through exhaust fans, and the softened membrane around those fans gets cut out and replaced with a resistant one.
Repair around restaurant exhaust fansCollect what every tenant under that roof section has seen. It is the fastest way to find a source on a shared roof.
Multi-tenant roof leak tracing follows the same order every time, across every unit involved.
Tenant reports come in first, then the crew walks each affected unit and the roof above the whole run, including parapets, scuppers, and every rooftop unit.
Each owner or the landlord signs off before anyone steps onto their section, and roof hatch keys get arranged ahead of time.
Suspect areas get water tested one at a time while tenants watch inside, so the source gets pinned to one unit.
Flashing, seams, or scuppers over the right unit get repaired with matching materials, and failed old patches come off.
Photos and notes go to the landlord and the tenants involved, showing where the water started and what was fixed.
Clinics, retail rows, churches, and flex buildings fill out the rest of our repair area. Not on the list? Call us or send us a message.
Fort Mitchell is the next largest town in the area. Its repair calls center on gutters and downspouts, and on where repaired drainage sends roof water.
Fort Mitchell Commercial Roof Repair →Answers for landlords, property managers, and tenants on shared roofs.
Across tenant lines, because water often enters over one unit and drips inside the next. Leak reports from every tenant under the roof section come first, then parapets, scuppers, and units across the run get checked and water tested one area at a time.
Whoever controls the roof, usually the landlord or property manager, since access to each section needs their sign-off. Tenants can still call to report a leak, and their notes help when the landlord schedules the visit.
Each rooftop unit is a seam in the waterproofing. When a tenant's unit gets serviced or swapped, torn base flashing or an unsealed curb opening sends water under the membrane toward the next unit.
In most cases. Base flashing and counterflashing work happens around the unit while it runs. When the unit has to be lifted, the HVAC contractor and an inspection get booked so the shutdown stays short.
Roofs over several storefronts collect patches from many contractors. A log of dates, locations, and materials shows which patches are holding and keeps the next crew from patching over a failed one.
Scope decides it. A seam or a pipe boot is a different scale from deck work or a unit swap. Planning and Development Services of Kenton County issues building permits for Elsmere, and describing the scope to them settles it.
Tell us which storefront shows the stain and who controls roof access. We trace it across the whole run.